CASE STUDY: Hydraulic crossing

This case study demonstrates the increased performance possible using AM techniques. Here Selective Laser Melting (SLM) allowed designers to realise significant increases in performance in hydraulics by exploiting the possibilities of this Additive Manufacturing process.

Inside the hydraulic crossing two fluid streams cross within a limited space without mixing. The conventionally produced part consists of a massive metal block where drilled and locked blind holes meet in two levels. The main bore splits into two smaller bores to keep the height and the possible mass flow constant. The weight of the conventionally produced pipe crossing is 20 kg and measures 230 x 230 x 50 mm.

Without being hindered by the limits of conventional production processes, the designer was free to optimise the functionality and in the AM produced hydraulic crossing the fluid flow was improved by adapting the internal channel geometry according to flow simulation results. Geometrical changes of cross section profiles can be manufactured without great effort.

additively-manufactured-hyd

fig17 An additively manufactured hydraulic crossing (left) with the internal channel geometry shown (right). Designed during EU-funded project CompoLight; built on an EOS M270 system at Fraunhofer IFAM

Concerning thermodynamics, fins inside the channels are feasible to improve thermal exchange processes and to increase the parts stiffness at the same time. The newly designed hydraulic crossing (above) was produced from a stainless steel material, with internal fins supporting the part during processing. The new components dimensions are 80 x 80 x 50 mm and the total weight is only 0.7 kg, resulting in a mass reduction of around 96%.

 

increased-performance

Comparison of pressure loss of conventionally and additively built hydraulic crossing

In this study the optimisation of the channel geometry has an enormous impact on the crossing’s performance and thus on the entire hydraulic system. At a mass flow of 100 l/min, the pressure loss of the new design is reduced to only 20% of the pressure loss of the conventionally designed and manufactured part. Additionally, without any post-processing the surface quality of the AM part was sufficient to be flanged to the connecting piping. Even at a test pressure of 1400 bar, the part showed neither plastic deformation nor leakage.

 

>Next page: Back to Introduction

In the latest issue of Metal AM magazine

Download PDF
 

Extensive AM industry news coverage, as well as the following exclusive deep-dive articles:

  • What happens when you take the powder out of AM? Charting the rise of wire-based DED with WAAM3D
  • Smart sensor-integrated parts by AM: A look at a novel possibility with industrial applications
  • Tailored materials for AM: How a 'powder kit' can achieve greater material diversity with fewer resources in PBF-LB
  • QuesTek's ICMD: Faster, cheaper, and better alloy development for Additive Manufacturing
  • NanoAL: Alloy development on an open parameter PBF-LB machine, from installation through to Rapid Alloy Screening
  • Using the Six Sigma method to optimise metal powder spreading in PBF-LB
  • Insights from R&D to part production: How CT analysis can advance metal Binder Jetting
  • Corrosion and wear resistence of materials processed by beam-based AM technologies

The world of metal AM to your inbox

Don't miss any new issue of Metal AM magazine, and get the latest industry news. Sign up to our twice weekly newsletter.

Sign up

News from the industry…

    News from the industry…

    Discover our magazine archive…

    The free to access Metal Additive Manufacturing magazine archive offers unparalleled insight into the world of metal Additive Manufacturing from a commercial and technological perspective through:

    • Reports on visits to leading metal AM part manufacturers and industry suppliers
    • Articles on technology and application trends
    • Information on materials developments
    • Reviews of key technical presentations from the international conference circuit
    • International industry news

    All past issues are available to download as free PDFs or view in your browser.

    Browse the archive

    Looking for AM machines, metal powders or part manufacturing services?

    Discover suppliers of these and more in our comprehensive advertisers’ index and buyer’s guide, available in the back of Metal AM magazine.

    • AM machines
    • Process monitoring & calibration
    • Heat treatment & sintering
    • HIP systems & services
    • Pre- & post-processing technology
    • Powders, powder production and analysis
    • Part manufacturers
    • Consulting, training & market data
    Download PDF
    Share via
    Copy link
    Powered by Social Snap